What Grit to Sand Epoxy Between Coats: The Complete Professional Guide

Feb 10, 2026

Sanding epoxy between coats is one of the most critical—and most misunderstood—steps in achieving a strong bond, smooth finish, and long-lasting epoxy floor or surface. Using the wrong grit can lead to poor adhesion, visible scratches, peeling, or premature coating failure.

This guide explains exactly what grit to sand epoxy between coats, why it matters, how grit selection changes based on epoxy type and condition, and how professionals ensure optimal mechanical bonding between layers. Whether you’re a DIY homeowner, contractor, or installer, this article covers everything you need to know to get professional-grade results.

Why Sanding Epoxy Between Coats Is Necessary

Epoxy relies on mechanical adhesion when applying additional coats outside the chemical recoat window. Once epoxy begins to cure, it forms a hard, non-porous surface. Without sanding, the next layer has nothing to grip.

Sanding between coats helps to:

  • Create microscopic scratches for mechanical bonding
  • Remove surface contaminants like dust, oils, or amine blush
  • Level imperfections such as roller marks, bubbles, or debris
  • Ensure uniform sheen and finish consistency

According to coating manufacturers and industry data, improper surface prep is responsible for over 80% of epoxy coating failures, with insufficient sanding being a leading cause.

Recommended Grit to Sand Epoxy Between Coats (Quick Answer)

For most epoxy applications:

  • 80–100 grit → Heavy leveling or correcting major imperfections
  • 100–120 grit → Standard sanding between epoxy coats (most common)
  • 120–150 grit → Light scuff sanding for adhesion without deep scratches
  • 180–220 grit → Final smoothing or sanding before clear coats

The industry standard for sanding epoxy between coats is 100–120 grit.

This range provides the ideal balance: aggressive enough to promote adhesion, but fine enough to avoid visible scratch marks telegraphing through the next coat.

Choosing the Right Grit Based on Epoxy Condition

Fresh Epoxy (Within Recoat Window)

If you’re recoating within the manufacturer’s chemical recoat window (often 12–24 hours):

  • Sanding may not be required
  • Light scuff with 120–150 grit is still recommended for consistency

Fully Cured Epoxy

If the epoxy has fully cured:

  • Sanding is mandatory
  • Use 100–120 grit for proper mechanical bonding

Uneven or Defective Epoxy Surface

For runs, drips, bubbles, or roller lines:

  • Start with 80–100 grit
  • Follow with 120 grit to refine scratches

Grit Selection by Application Type

Epoxy Floor Coatings (Garages, Warehouses, Shops)

  • Recommended grit: 80–120
  • Floors require stronger mechanical bonding due to traffic loads

Epoxy Countertops & Furniture

  • Recommended grit: 120–150
  • Focus on smoothness and visual finish

Metallic Epoxy Systems

  • Recommended grit: 120 grit
  • Prevents disruption of metallic pigments

Epoxy Before Clear Coat or Polyaspartic Topcoat

  • Recommended grit: 150–220
  • Ensures smooth finish without visible scratches

What Happens If You Use the Wrong Grit?

Grit Too Coarse (Below 80)

  • Deep scratches visible through topcoat
  • Poor visual finish
  • Increased material usage to fill scratches

Grit Too Fine (Above 220)

  • Inadequate surface profile
  • Reduced adhesion
  • Higher risk of delamination or peeling

Coating manufacturers typically specify a CSP (Concrete Surface Profile) equivalent, and sanding with 100–120 grit closely aligns with CSP-2 to CSP-3, which is ideal for epoxy adhesion.

Proper Sanding Process Between Epoxy Coats

Step 1: Confirm Cure Time

Ensure the epoxy is firm enough to sand without gumming up abrasives.

Step 2: Use the Right Equipment

  • Orbital sander (for flat surfaces)
  • Hand sanding for edges and corners
  • Floor buffer or grinder for large areas

Step 3: Sand Evenly

  • Avoid over-sanding one area
  • Focus on dulling the entire surface evenly

Step 4: Clean Thoroughly

After sanding:

  • Vacuum all dust
  • Wipe with acetone or denatured alcohol
  • Ensure surface is clean, dry, and residue-free

Dust contamination is a common cause of fisheyes and bonding issues in subsequent coats.

Do You Always Need to Sand Between Epoxy Coats?

Not always, but often.

You can skip sanding only if:

  • You are within the epoxy’s chemical recoat window
  • The surface is clean and defect-free
  • Manufacturer guidelines explicitly allow it

However, professional installers frequently sand even within the recoat window to ensure uniform adhesion and finish quality.

Professional Tips for Best Results

  • Always follow the epoxy manufacturer’s technical data sheet (TDS)
  • Change sandpaper frequently—clogged abrasives reduce effectiveness
  • Avoid steel wool or polishing pads between coats
  • Maintain consistent grit across the entire surface
  • When in doubt, 100–120 grit is the safest choice

Key Takeaway: Best Grit to Sand Epoxy Between Coats

For the majority of epoxy applications:

Use 100–120 grit sandpaper to sand epoxy between coats

This grit range provides:

  • Reliable mechanical adhesion
  • Smooth, professional finish
  • Reduced risk of coating failure

Proper sanding isn’t optional—it’s what separates epoxy coatings that fail in months from those that perform for years.

0

Your Cart

Quantity: 0 Items: 0
No Product in the Cart!
$0.00
$0.00
$0.00